Blog

Orange County-Ca HP DesignJet T1300ps/T1300 Plotter Printer Large Format Repair | Service

January 13, 2021

Cleaning – Lubrication – Calibration – Free

Error code
Recommendation
01.0, 01.1, 01.2
Restart the printer.
06:03
Restart the printer.
08:04
Restart the printer. If the problem persists, update the printer’s firmware. See Update the firmwareUpdate the firmware.
08:08
Retry the operation that you were attempting. If it fails again, restart the printer. If the problem persists, update the printer’s firmware. See Update the firmwareUpdate the firmware.
21, 21.1, 21:03, 21.1:03, 21:13, 21.2:13, 22.0, 22.1, 22.2, 22.3, 22.x:03, 24
Restart the printer.
26:01, 26.x:01
Bad contact detected in an ink cartridge (if present, x refers to the cartridge in slot x). Remove and reinsert the cartridge. If necessary, insert a new cartridge.
26:14
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
27:01, 27.x:01
Too many printhead nozzles are not working (if present, x refers to the printhead in slot x). Remove and reinsert the printhead, or try cleaning the electrical connections. If necessary, insert a new printhead. See The front-panel display recommends reseating or replacing a printheadThe front-panel display recommends reseating or replacing a printhead.
27:03
Printhead error. Restart the printer.
27:14
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
31:03, 41:03, 42:03, 45.1:03, 45.2:03, 47:03, 56:03
Restart the printer.
61:01
The file format is wrong and the printer cannot process the job. You may have sent a PostScript, PDF, TIFF or JPEG job to a non-PostScript printer. If the job is password-protected, try sending it without password protection. Otherwise, update your printer’s firmware and try again. See Update the firmwareUpdate the firmware.
61:04.1, 61:04.2
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
61:08.1
Resend the job without password protection.
62, 62:04, 63
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
63:01
The printer has failed to get an IP address. Connect to another network or change the IPv4 configuration.
63:04, 64
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
64.1:01
The external hard disk has been removed while it was in use. Please reconnect it and restart the printer.
64:04, 65, 65:04
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
66:08
The job cannot be printed on the paper type that is loaded.
67, 67:04
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
68:03
Restart the printer.
71.04
Out of memory. To avoid this, in the HP-GL/2 and HP RTL driver select the Advanced tab and then Send job as a bitmap.
71:03
Restart the printer.
71:04
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
74:04, 74.1:04
The firmware upgrade has failed. Press OK and try again. See Update the firmwareUpdate the firmware.
74.1
Try the firmware update again. Do not try to use your computer while the update is in progress.
74.8:04
The firmware upgrade has failed. Your firmware file may be incorrect; try to download it again. See Update the firmwareUpdate the firmware.
76:03
Restart the printer.
77:04, 78.1:04
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
78:08
Borderless printing not possible; setting ignored..
79:03
Restart the printer.
79:04, 79.1:04
Update your printer’s firmware. See Update the firmwareUpdate the firmware.
81:01
Please follow the instructions on the front panel. You may be asked to run a test procedure and write down a numeric code before contacting HP Support. See Contact HP SupportContact HP Support.
81:03, 84:03
Restart the printer.
86:01
Please follow the instructions on the front panel. You may be asked to run a test procedure and write down a numeric code before contacting HP Support. See Contact HP SupportContact HP Support.
94, 94.1, 94:08
Restart color calibration. See Color calibrationColor calibration.
94:02
Color calibration failed. Check that the paper type that is loaded corresponds to the paper type that you have selected.

ORANGE COUNTY – Ca Aliso Viejo, CA. Anaheim, CA. Anaheim Hills, CA. Atwood, CA. Brea, CA. Buena Park, CA. Capistrano Beach, CA. Corona del Mar, CA. Costa Mesa, CA. Coto de Caza, CA. Cypress, CA. Dana Point, CA. El Toro, CA. Foothill Ranch, CA. Fountain Valley, CA. Fullerton, CA. Garden Grove, CA. Huntington Beach, CA. Irvine, CA. La Habra, CA. La Palma, CA. Ladera Ranch, CA. Laguna Beach, CA. Laguna Hills, CA. Laguna Niguel, CA. Laguna Woods, CA. Lake Forest, CA. Los Alamitos, CA. Midway City, CA. Mission Viejo, CA. Monarch Beach, CA. Newport Beach, CA. Orange, CA. Placentia, CA. Rancho Santa Margarita, CA. San Clemente, CA. San Juan Capistrano, CA. Santa Ana, CA. Santa Ana Heights, CA. Seal Beach, CA. Silverado, CA. South Laguna, CA. Stanton, CA. Sunset Beach, CA. Surfside, CA. Trabuco Canyon, CA. Tustin, CA. Villa Park, CA. Westminster, CA. Yorba Linda, CA. designjet repair, Service, Carriage belt replacement, Broken carriage belt, Print-head error, Ink supply error, Paper not cutting, Noisy, Error code, No power faulty power supply, Clean plotter Carriage Rails, Lubricate the plotter Carriage Rails, Cleaning the Drive Roller, Encoder Strip Cleaning and inspection, Inspect and Clean Platen Assembly, Adjust the designjet print head after exchanging the belt,HP DesignJet Carriage belt replacement, HP Designjet Fix error code,